Nissan titan rockstar wheels12/18/2023 25? Rims would stick out 2.5" more than stock, for a 9" width rim, and would have 4" backspacing. With 35s even my friend's 6" PC stage 1 lifted Titan needed to cut a little with the old version of the 35x12.5R17 BFG M/T. Popular size for thr pinch weld mod, but shouldn't be too bad with 33s. This would be my pick if I could run spindles. You'd likely have CST spindle rubbing with wide tires though with 5.75" backspacing.Ġ? Rims stick out 1.5" more than stock. +18? 3/4" more than stock SE/LE rims, (an inch more if you also count the tires' extra width, which stick out about 1/4" more, as far as section width). check out these posts by PRG:Īs for the offset on a 9" width rim, and how far the rims would stick out compared to stock: Sort of like a free 4".Īdding level kits to the coilovers is a bad idea. You can run your stock coilovers, or stock application ones, like the Icons, SAWs, or the 2" body Radflo, or any OEM compatible like the Bilstein HD with them, as well as leveling kits, and still use the stock UCA, unless going above their normal maximums. had coffee too late and couldn't sleep.įor the lift you'd be better off getting spindles right away. CUMMINS TITAN!!Ĭlick to expand.No problem. If I wanted to lift a truck that high I'd buy a diesel so I can still get some mileage. I don't really want to run bigger than a 33" tire though so I doubt I will lift 8". how much do I stick out over stock with:ĭistant future: Possibly go with a 4" spindle lift. I could possibly get them to cut a 0 offset. I don't think I want a +18 offset and am not sure if RBP will make that for me. Nick at RBP said that the rim he would cut for me would be 4.5" backspacing. I don't want to chip my paint but I do like the look of the tires sticking out. I want to avoid running fender flares if at all possible. I think I have attached photos of them (first time.) Nick said he was going to get the computer boys at RBP to change that. Also, to answer your question, they do sell 20x9. I want to keep the toyo's and run the 94R 20x9 black&machined rim (New rim - they just came out with it). Run 2.5" spacer in rear and bilstein 5100 for a total of 3" lift in the rear. Near future: Buy 08 springs and bilstein 5100s to raise my front end an additional 2" (4" total lift with leveling kit). Thank you NorCal, you're the shiz when it comes to this. Note: If you have or plan to buy the CST 4" spindles or a CST bracket lift, keep backspacing at 5" or less, for wide tires to avoid tire to spindle rub. For them I'd look for an offset of +6 mm to +18 mm giving 5" to 5.5" backspacing, respectively:Ģ0x8.5" Wheel Products - Discount Tire Direct There are a few other 9" width wheels with +18 mm offset on these pages, +12 mm for a 5.5" backspacing would be fine too:Ģ0x9" Wheel Products - Discount Tire DirectĪ lot of the 12.5" width tires call for a minimum of an 8.5" width rim. Here is an example of one that sort of reminded me of the RBP. If I were to get a 9, it would have a a +18mm offset and therefore about 5.75" of backspace, and it would still stick out 3/4" more than the stock rims. That way you have the option of later running taller tires if you decide to. Like idiotsaray mentioned, a narrower rim and 0 offset or positive offset is the way to go. With the pinch weld mod you could make it work, but they will stick out about 1-1/2" more than stock SE/LE rims. So even though your 20x9 rims would stick out 1/2" less, they may rub some. But they don't have as large of lugs at the shoulder as the Toyo M/T. This tire has about the same 12-1/4" section width on a 9" width as a Toyo M/T. With -12 mm offset it has 4.5" of backspacing, and the tires can rub on on leveled Titan with 33.2" diameter LT295/70R17 Nitto Terra Grappler A/T. Click to expand.Where did you see RBP 20x9's? All I saw were 20x10s and they were crazy expensive.Ī 9" width rim with 0 mm of offset will have 5" backspacing.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |